Scroll export button | ||||||||
---|---|---|---|---|---|---|---|---|
|
Info |
---|
This Guide leads you through installation and provisioning of W-AIR Small Business solution. Support starts from 5.02.20201228.4 / 4.04.45355.09. Useful links:
Created: January 2021 Updated: February 20222023 Permalink: https://wildix.atlassian.net/wiki/x/2BrOAQ |
Table of Contents |
---|
Description
...
Wildix W-AIR handsets: W-AIR BasicBasic2, W-AIR LifeSaver, W-AIR Med, W-AIR Office and W-AIR Headset. Follow the online Guides to get detailed information: W-AIR DECT Handsets Guide, W-AIR Headset Guide.
W-AIR Small Business solution
Supports of PoE IEEE 802.3af Class 2
- Up to 20 users per system
- Up to 10 concurrent calls*
- Up to 10 channels using G.711 codec
- Up to 4 channels using G.729 codec
- Up to 6 repeaters per base
- No multicell
- Base station indoor range: 50 m; outdoor range: 300m
Note |
---|
*Enabling PTT feature (Push-to-talk) on W-AIR handsets reduces the number of available channels to 6. |
...
- Base station unit x 1
- Cat. 5 Ethernet cable x 1
Power supply adapter is not included (item can be ordered separately, code: PS-5V2A)
W-AIR Repeater:
- Power adapter x 1
- Repeater unit x 1
Base
...
station connection and reset
Reset a base station: press the Reset button for more than 2 seconds.
...
Open W-AIR SB web interface -> Extensions menu and select the handset you want to remove (click on the IPEI value):
The Handset menu opens; enter the value “FFFFFFFFFF” into the field “IPEI” and click Save:
- Register a new handset to the W-AIR base station: on the handset open the menu Connectivity -> Register; after the new handset is registered, it appears on the W-AIR SB web interface -> Extensions menu
- Access the PBX via SSH and add PBX parameter “ResetHandset=yes” to the [wildixair] section of the /rw2/etc/provision.conf. Documentation: Provisioning Custom Settings
- Perform logout procedure: dial 99 from the handset and follow the prompts
- Remove PBX parameter “ResetHandset=yes” from the [wildixair] section of the /rw2/etc/provision.conf[wildixair]
Step 3. Assign a W-AIR Handset to User
You can assign W-AIR handset to a user via the handset itself or via WMS (starting from WMS 5.04.20220309.1).
Assigning via the handset
...
Example: PIN is 4Ag7$Zl@, you have to dial 4247*
Follow W-AIR DECT Handset - User Guide to get more details.
Note |
---|
Admin password is also accepted. |
...
Note |
---|
Note: The support starts from WMS 5.04.20220309.1. |
Go to WMS -> Devices -> W-AIR devices
Choose the handset and click Assign to user
Enter user extension and click Save
Note |
---|
Note: To figure out which handset received the assigned extension, you can dial this extension and see which handset rings. |
...
- Choose the handset -> click Assign to user
Select “unknown” in the Extension field
- Click Save
Step 4. Set up Repeaters
...
Note |
---|
W-AIR Upgrade logic in WMS 5.03. Starting from WMS version 5.03.20210709.3, W-AIR System is upgraded according to the following policies:
|
...
When there is the new FW available, the notification "Firmware available" appears in WMS -> Device Devices.
To upgrade the FW, select one or multiple base stations, and click Configure/Sync. Wait for several minutes, during the FW upgrade, devices are rebooted. As soon as the upgrade procedure is finished, the new FW version appears in the Devices menu of the WMS, the base stations are no longer marked with the blue color.
...
- Go to the menu Extensions
Click on the “IPEI” of the handset:
The following window is displayed, allowing you to set up emergency settings:
Modify the parameters:
- “Alarm Line”: select the handset’s extension number
“Alarm Number”: Enter the number to be called when the alarm is triggered from the handset
Note You can enter an extension number that must be called or customize the service by modifying the Dialplan in the WMS and to add the “Alarm Number” as a Called number into a Dialplan procedure.
Tick off the Profiles that you wish to enable for this handset
Click Save on the bottom of the page
Go to Management menu and click Save and reboot to reboot the base station and apply the new parameters
...