A quick guide to connection, installation and troubleshooting of WSG05POE-WSG08POE-WSG16POE-WSG24POE.
Updated: January 2017
Permalink: https://confluence.wildix.com/x/JgNKAw
Package contents
- 1 x Switch
- 1 x Power cord (WSG08/16/24POE)
- Rubber feet, mounting ears and screws for rack installation (WSG08/16/24POE)
Installation
- All models can be installed on a flat surface; WSG08/16/24POE are rack-mountable; WSG05POE is wall-mountable
- Install in a cool and dry place (see the datasheet for acceptable tº and humidity ranges)
- Leave the space around the switch for ventilation
- Install the switch on a surface that can support its weight
- Do not place heavy objects on the switch
- The power cord length is less than 150cm
Turn on the switch
Before powering on the switch, make sure the voltage is correct. The power supply socket is situated on the back panel of the switch.
Plug the power supply into the switch: the power indicator on the front panel must turn on.
LED indicators and ports description
WSG05POE
- 5 x 10/100/1000Mbps Auto-negotiation Ethernet RJ45 ports (1 PoE IN port and 4 PoE OUT ports)
LED indicators are located on the RJ45 connector
LED | Description |
Power | Power is supplied |
Link/Act | A valid link is established |
WSG08POE
- 8 x 10/100/1000Mbps Auto-negotiation Ethernet RJ45 ports with 8 PoE function ports
LED | Color | Status | Description |
PWR | Green | ON | Power is supplied |
OFF | No power | ||
Link | Orange (10/100Mbps) Green (1000Mbps) | ON | A valid link is established |
Blinking | Data packets are received or transmitted | ||
OFF | No link is established | ||
PoE | Orange | ON | A PoE PD (Powered Device) is connected to the port |
OFF | No PD is connected to the port | ||
MAX 1 (1-4 Ports) | Yellow | ON | The power output has reached the max power budget (⋝55W) |
Blinking | The power output has exceeded the max power budget (⋝70W) | ||
OFF | The power of all the connected PoE ports is less than 55W | ||
MAX 2 (5-8 Ports) | Yellow | ON | The power output has reached the max power budget (⋝55W) |
Blinking | The power output to PDs has exceeded the max power budget (⋝70W) | ||
OFF | The system is using less than 55W |
WSG16POE
- 16 x 10/100/1000Mbps Auto-negotiation Ethernet RJ45 ports with 16 PoE function ports
LED | Color | Status | Description |
Power | Red | ON | Power is supplied |
OFF | No power | ||
Link / Act / Speed | Orange (10/100Mbps) Green (1000Mbps) | ON | A valid link is established |
Blinking | Data packets are received or transmitted | ||
OFF | No link is established | ||
PoE | Yellow | ON | A PoE PD (Powered Device) is connected to the port |
OFF | No PD is connected to the port |
WSG24POE
- 10/100/1000Mbps RJ45 ports (1-24): connect devices with 10 / 100 / 1000Mbps bandwidth.
- SFP ports (SFP1, SFP2): install SFP module and connect devices with 1000Mbps bandwidth.
- Console port (Console): connect a serial port of PC / terminal for monitoring and configuring the Switch.
- Reset button (Reset): (device is connected to power supply) press and hold the button for about 5 sec.
See WSG24POE – Admininstrator Manual for more info on configuration of the web managed switch.
LED | Color | Status | Description |
PWR | Green | ON | Power is supplied |
OFF | No power | ||
Link / Act / Speed (1-24) | Orange (10/100Mbps) | ON | A valid link is established |
OFF | No link is established | ||
Green (1000Mbps) | Blinking | Data packets are received or transmitted | |
Link / Act / Speed (SFP1,2) | Green | ON | A valid link is established |
OFF | No link is established | ||
Blinking | Data packets are received or transmitted | ||
PoE (1-24) | Yellow | ON | A PoE PD (Powered Device) is connected to the port |
OFF | No PD is connected to the port | ||
Blinking | The PoE power circuit may be in short or the power current may be overloaded. |
Connection of devices
Connect devices to the ports of the Switch using a network cable (check the datasheet for more information).
WSG05POE
1 PoE IN into 4 PoE OUT 10/100/1000 Mbps half/full duplex ports.
PoE Input: Pin Assignment and Polarity: Both 1/2 (-), 3/6 (+) and 7/8 (-), 4/5 (+)
PoE Output: Pin Assignment and Polarity:1/2 (-), 3/6 (+)
Output Power: up to 12W for 4 PSE or 25W for 2 PSE
Application example (60W PoE injector is optional)
Multiple PoE Extenders can be connected every 100 meters to obtain greater distances.
Examples for medium PoE devices (PoE Class 2 under 6W):
PoE Source | |
PoE switch 802.3at, Output: 50V | 60W mid span 802.3at, Output: 54V |
Max Distance | |
200m | 300m |
WSG08POE/WSG16POE
All the ports have PoE power supply function
WSG24POE
1-24 ports have power supply function (see the datasheet for the max power output)
Switch login (WSG24POE)
Check that the IP address of the PC is within the range of the default IP address of the switch (192.168.2.XXX)
- Default IP address: 192.168.2.1
- User name: admin
- Password: admin
Troubleshooting
If Link indicator does not light up after making a connection, make sure that:
- the network interface, network cable, or switch port is not damaged or defective
- the proper cable type is used and its length does not exceed specified limits (see the datasheet)
- cable is plugged into both the Switch and a PoE Powered Device
If the Power indicator does not turn on when the power cord is plugged in, make sure that the power outlet or the power cord is not damaged.
Make sure that you use standard RJ-45 cables. Cables that does not meet the standards of the sequence of data may slow down the data transmission speed or even block it.