In this Admin Guide you can find
Updated: March 2018
Permalink: https://confluence.wildix.com/x/KQg8AQ
You can set some provision variables, which change result provision file for device. All changes you have to do in the file /rw2/etc/provision.conf (ini syntax - http://en.wikipedia.org/wiki/INI_file).
You can set for all the devices by adding updating section [general]. the parameter for specified device by updating one of the sections:
- [wildixp] - WP
- [wildixp2] - WP480R2
- [wildixfxo] - W04FXO
- [wildixgw] - Media5
- [wildixair] - WAIR
Note: access the file using the command:
nano-tiny /rw2/etc/provision.conf
It is also recommended to access the file via root.
List of supported settings:
- To set SIP Server Port of the registered account in the device:
SIPServerPort=0-65535
- To set SIP Server Port of the registered account in the device behind NAT:
SIPServerPortRemote=0-65535
- To set SIP transport protocol of the registered account in the device:
SIPTransport=UDP|TCP|TLS
- To set SIP transport protocol of the registered account in the device, located behind NAT. Choose one of the protocols:
SIPTransportRemote=UDP|TCP|TLS
- To disable/ enable force using HTTP protocol instead HTTPS for all request from the device, like provision, phonebook, features, etc. Note: device should be re-provisioned. Supported only by WP and WP480R2)
HTTPForceUse=yes|no
- To disable/ enable raw scanning method in case of automatic provision (useful feature for PBX inside chroot environment). (available only for [general] section):
RawScan=enable|disable
To set BLF transfer type. (Note: only for wildixp section. Supported only by wp480, wp490 and wp600):
BLFTransType=attended|blind
To enable/ disable making provision authorization for local devices. (available only for [general] section):
RequireAuth=yes|no
To enable/ disable an automatic adding local device to provision database (Note: for W-AIR you have create network manually via WMS interface) (availbale only only for general section)
TrustLocalDevice=yes|no
To enable/disable the wp2015 power led. (Note: no - disables power led, otherwise - enabled) (Note: only for [wildixp2] section)
POWER_LED=yes|no
To set the time in seconds during which the LED of a missed event (call or voice mail) will blink. If "0" - blink always, if "1" - blink only once. (Note: only for [wildixp2] section)
PowerLEDBlinkTime=0-14400
- To hide/ show DTMF visualisation on displays of phones. (no - show , yes - hide):
HIDE_DTMF=yes|no
To enable/ disable the pin-protection for the voicemail-menu. Important: removed in rev 39338. Clients must use "can use"/"cannot use" "Voicemail without pin code" ACL instead.
XMLBrowserAuth=yes|no
To set only g711 codecs (if g711only= yes) to w-air bases. The setting is implemented only for W-AIR Bases parameter available only for w-air bases) Note: only for [wildixair] section
g711only=yes|no
To set "Reset handset" provision mode. Disabled by default. Set to "yes" in case if you need to delete an handset ipei from w-air sb and allow to reuse the slot. After slot is cleared, you need to disable this parameter. (Note: only for [wildixair] section)
ResetHandset=yes|no
To disable g729 codecs (if DisableCodecG729=yes) to w-air sb (Note: the parameter available only for w-air sb) (Note: only for [wildixair] section)
DisableCodecG729=yes|no
To set parameter to control Packet Loss. Network Problem Threshold 1-99, 100 - disable. (Note: device should be re-provisioned. Supported only by WP4x0)
LossPktRateMin=0-100
To set parameter to control Packet Loss. Critical Network Problem Threshold 1-99, 100 - disable. Device should be re-provisioned. Supported only by WP4x0)
LossPktRateMax=0-100
BLF will blinks in case when monitored user has active call+incoming call if "ActiveAndIncomingCall" or keep the old behavior if "ActiveCall". Default is old behavior. (Note: only for [wildixp2] section)
BLFNotifyType= ActiveCall | ActiveAndIncomingCall
To force the failover PBX (SIP Server 2) with the value. Only ip addresses allowed (available only for [wildixp2] section):
FailoverPbxIp=<IP address>
Limitation for section configuration
You have to add empty section for loading parameters from [general] section.
For example you added parameter HTTPForceUse = yes to general section. You have to add empty section wildixp2 if you want to apply this parameter for WPR2 devices.
WP2015 does not apply the parameter POWER_LED and PowerLEDBlinkTime without rebooting the device.