Page Comparison

SIPServerPort

=0-65535 

SIPServerPortRemote

=0-65535

SIPTransport

=UDP|TCP|TLS 

set SIP transport protocol of the device registered to the account

SIPTransportRemote

=UDP|TCP|TLS

HTTPForceUse

=yes|no 

RawScan

=enable|disable

BLFTransType

=attended|blind

only for [wildixp] section. Set BLF transfer type. Supported only by WP480, WP490, WorkForce, WelcomeConsole and WP600

RequireAuth

only for [general] section. Enable/ disable the authorization when provisioning local devices. Note: not available starting from WMS Version 3.88.41047.24

TrustLocalDevice

=yes|no

POWER_LED

=yes|no 

only for [wildixp2] section. This parameter allows disabling the missed call LED on WP4X0 2015 phones, WorkForce, WelcomeConsole (this setting is normally applied in Hotels). Enable/ disable WP 2015 Power LED ("no" - disable, "yes" - enable); you can also change the behavior of the power LED by using the parameter PowerLEDBlinkTime (described below)

PowerLEDBlinkTime

=0-14400

HIDE_DTMF

=yes|no

XMLBrowserAuth

=yes|no 

enable/ disable PIN protection for the Voicemail via XML (via the phone menu)

g711only

=yes|no

ResetHandset

=yes|no

only for [wildixair] section. The parameter is disabled by default ("yes" - enable, "no" - disable). Enable it in case you need to delete a Handset IPEI from W-AIR SB and allow to reuse the slot. When it is done, you need to disable it

DisableCodecG729

=yes|no 

only for [wildixair] section. Disable g729 codecs ("yes" - disable, "no" - enable). The parameter is applied only to W-AIR Small Business Bases

LossPktRateMin

=0-100

LossPktRateMax 

=0-100

BLFNotifyType

=ActiveCall|ActiveAndIncomingCall

FailoverPbxIp

=<IP address>  

EnableMWISubscribe

=yes|no 

DisableShowUsername

=yes|no 

BaseMaxSIPReg

=4-30

only for [wildixair] section. Prior to 5.04, the default value is 20 accounts per 1 base. Starting from 5.04, the distribution is as follows:

• in W-AIR Network with 2 and more bases, the default number is 8 per 1 base
• in W-AIR Network with 1 base, the default number is 30 accounts

Edit it in case you need to change the number of SIP accounts before distributed load per base station (min. value = 4, max. value = 30)

OffHookDialOut 

=yes|no

SidetoneHandset

=0-7

SidetoneHeadset

=0-7

EnableReasonCause

=yes|no

w-air-sb-pin

=0000-9999

MelodyBLF

=yes|no

SRTPForceUse 

=yes|no

only for [wildixgw], [wildixfxo3] and [wildixfxs2] sections. The parameter is enabled by default for [wildixgw] starting from WMS version 5.01 and for [wildixfxo3] and [wildixfxs2] sections - starting from WMS version 5.03 (no - disable, yes - enable). It enables Direct SDES-SRTP support between BRI/ PRI media gateways (EOL)

LLDP

=yes|no

LLDPInterval

=10-3600

AuthLockTimeout

=>=0

DelayAfterOffhook

=1-255

SpeakerDisable

=yes|no|<list of extensions>

only for [wildixp2] section. The parameter allows to disable speaker mode on WorkForce. By default, the speaker mode is on (yes - disable the speaker mode for all WorkForce devices, no - enable it, <list of extensions> (e.g. SpeakerDisable=380,240,220) - disable the speaker mode for the mentioned extensions only). Note: the parameter is available starting from WMS 5.04.

WideNarrowbandUse

=yes|no

only for [general] section. The parameter allows to manage wideband codecs usage. By default, the parameter is disabled and wideband codecs are forced for all devices. When the parameter is enabled (WideNarrowbandUse=yes), the previous behaviour remains: all devices use wideband codec priority or narrowband codec priority and remote codecs priority or local codecs.

Notes: In case of WideNarrowbandUse=yes, you need to add relevant lines to etc/callweaver/sip-wideband.conf to set the parameters (see more in Custom config parameters List - Manage wideband codecs usage)  

Note: the parameter is available starting from WMS 5.04.

ToneDetectByPeer

=yes|no

only for [wildixfxs2] section. When enabled, the parameter fixes an issue of slow fax reception speed which sometimes occurs in US/ Canada on FXSR3 devices. By default, the parameter is disabled.

Note: the support starts from WMS 5.04.

RXgain

=-10-10

only for [wildixfxs2] section. The parameter allows to modify the RX gain level on FXS r3 media gateways. The default value is -2 dB.

Note: the support starts from WMS Beta 6.01.

TXgain

=-10-10

only for [wildixfxs2] section. The parameter allows to modify the TX gain level on FXS r3 media gateways. The default value is 0 dB.

Note: the support starts from WMS Beta 6.01.

WairSilentcharging 

=on | off | deactivated

only for [wildixair] section. The parameter allows to control silent charging setting for x-hoppers headsets. Value "on" implies that only LED indication is used while charging; "off" suggests normal mode with LED indication and audio while charging; "deactivated" means headset is disconnected and can’t receive calls while charging. 

Note: the support starts from WMS 6.01.20221122.1.