In this Admin Guide you can find provisioning variables
Updated: March 2018
Permalink: https://confluence.wildix.com/x/KQg8AQ
You can set some provision variables, which change result provision file for device. All changes you have to do in the file /rw2/etc/provision.conf (ini syntax - http://en.wikipedia.org/wiki/INI_file).
You can set for all the devices by adding updating section [general]. the parameter for specified device by updating one of the sections:
- [wildixp] - WP
- [wildixp2] - WP480R2
- [wildixfxo] - W04FXO
- [wildixgw] - Media5
- [wildixair] - WAIR
Note: access the file using the command:
nano-tiny /rw2/etc/provision.conf
It is also recommended to access the file via root.
List of supported Custom Setting configurations:
SIPServerPort | =0-65535 | set SIP Server Port of the registered account in the device: |
SIPServerPortRemote | =0-65535 | set SIP Server Port of the registered account in the device behind NAT: |
SIPTransport | =UDP|TCP|TLS | set SIP transport protocol of the registered account in the device: |
SIPTransportRemote | =UDP|TCP|TLS | set SIP transport protocol of the registered account in the device, located behind NAT. Choose one of the protocols: |
HTTPForceUse | =yes|no | To disable/ enable force using HTTP protocol instead HTTPS for all request from the device, like provision, phonebook, features, etc. Note: device should be re-provisioned. Supported only by WP and WP480R2) |
RawScan | =enable|disable | disable/ enable raw scanning method in case of automatic provision (useful feature for PBX inside chroot environment). (available only for [general] section): |
BLFTransType | =attended|blind | set BLF transfer type. Supported only by WP480, WP490 and WPp600) (Note: only for wildixp section.): |
RequireAuth | =yes|no | enable/ disable making provision authorization for local devices (available only for [general] section): |
TrustLocalDevice | =yes|no | enable/ disable an automatic adding local device to provision database (Note: for W-AIR you have create network manually via WMS interface) (availbale only only for general section) |
POWER_LED | =yes|no | enable/disable the wp2015 power led. (Note: no - disables power led, otherwise - enabled) (Note: only for [wildixp2] section) |
PowerLEDBlinkTime | =0-14400 | Set the time in seconds during which the LED of a missed event (call or voice mail) will blink. If "0" - blink always, if "1" - blink only once. (Note: only for [wildixp2] section) |
HIDE_DTMF | =yes|no | hide/ show DTMF visualisation on displays of phones (no - show , yes - hide): |
XMLBrowserAuth | =yes|no | enable/ disable the pin-protection for the voicemail-menu. Important: removed in rev 39338. Clients must use "can use"/"cannot use" "Voicemail without pin code" ACL instead. |
g711only | =yes|no | set only g711 codecs (if g711only= yes) to w-air bases. The setting is implemented only for W-AIR Bases parameter available only for w-air bases) Note: only for [wildixair] section |
ResetHandset | =yes|no | set "Reset handset" provision mode. Disabled by default. Set to "yes" in case if you need to delete an handset IPEI from W-AIR SB sb and allow to reuse the slot. After slot is cleared, you need to disable this parameter. (Note: only for [wildixair] section) |
DisableCodecG729 | =yes|no | disable g729 codecs (if DisableCodecG729=yes) to w-air sb (Note: the parameter available only for w-air sb) (Note: only for [wildixair] section) |
LossPktRateMin | =0-100 | set parameter to control Packet Loss. Network Problem Threshold 1-99, 100 - disable. (Note: device should be re-provisioned. Supported only by WP4x0) |
LossPktRateMax | =0-100 | set parameter to control Packet Loss. Critical Network Problem Threshold 1-99, 100 - disable. Device should be re-provisioned. Supported only by WP4x0) |
BLFNotifyType | = ActiveCall | ActiveAndIncomingCall | BLF will blinks in case when monitored user has active call+incoming call if "ActiveAndIncomingCall" or keep the old behavior if "ActiveCall". Default is old behavior. (Note: only for [wildixp2] section) |
FailoverPbxIp | =<IP address> | Force the failover PBX (SIP Server 2) with the value. Only ip addresses allowed (available only for [wildixp2] section): |
Limitation for section configuration
You have to add empty section for loading parameters from [general] section.
For example you added parameter HTTPForceUse = yes to general section. You have to add empty section wildixp2 if you want to apply this parameter for WPR2 devices.
WP2015 does not apply the parameter POWER_LED and PowerLEDBlinkTime without rebooting the device.