Document description
Updated:
Permalink:
You can set some provision variables, which change result provision file for device. All changes you have to do in the file /rw2/etc/provision.conf (ini syntax - http://en.wikipedia.org/wiki/INI_file).
You can set parameter for specified device by updating section [wildixp] - WP, [wildixp2] - WP480R2, [wildixfxo] - W04FXO, [wildixgw] - Media5, [wildixair] - WAIR or for all phone devices by updating section [general].
Note: it is recommended to access the file via
List of supported parameters:
- To set SIP Server Port of the registered account in the device:
SIPServerPort= 0-65535
- To set SIP Server Port of the registered account in the device, located behind NAT
SIPServerPortRemote=0-65535
- To set SIP transport protocol of the registered account in the device
SIPTransport=UDP|TCP|TLS
- To set SIP transport protocol of the registered account in the device, located behind NAT
SIPTransportRemote=UDP|TCP|TLS
- To disable/enable force using HTTP protocol instead HTTPS for all request from the device, like provision, phonebook, features, etc. Note: device should be re-provisioned. Supported only by WP and WP480R2)
HTTPForceUse=yes|no
- To disable/enable raw scanning method in case automatic provision (useful feature for PBX inside chroot environment). (Note: only for general section)
RawScan=enable|disable
To set blf transfer type. (Note: only for wildixp section. Supported only by wp480, wp490 and wp600)
BLFTransType=attended|blind
To enable/disable making provision authorization for local devices Note: only for general section)
RequireAuth=yes|no
enable/disable an automatic adding local device to provision database (Note: for W-AIR you have create network manually via WMS interface) (Note: only for general section)
TrustLocalDevice= yes | no
enable/disable the wp2015 power led. (Note: no - disables power led, otherwise - enabled) (Note: only for [wildixp2] section)
POWER_LED= yes | no
Set the time in seconds during which the LED of a missed event (call or voice mail) will blink. If "0" - blink always, if "1" - blink only once. (Note: only for [wildixp2] section)
PowerLEDBlinkTime = 0 - 14400
- hide/show dtmf visualisation on displays of phones. (no - show , yes - hide)
HIDE_DTMF=yes|no
enable/disable the pin-protection for the voicemail-menu. Important: removed in rev 39338. Clients must use "can use"/"cannot use" "Voicemail without pin code" ACL instead.
XMLBrowserAuth=yes|no
set only g711 codecs (if g711only= yes) to w-air bases (Note: the parameter available only for w-air bases) () Note: only for [wildixair] section
g711only=yes|no
set "Reset handset" provision mode. Disabled by default. Set to "yes" in case if you need to delete an handset ipei from w-air sb and allow to reuse the slot. After slot is cleared, you need to disable this parameter. (Note: only for [wildixair] section)
ResetHandset=yes|no
disable g729 codecs (if DisableCodecG729=yes) to w-air sb (Note: the parameter available only for w-air sb) (Note: only for [wildixair] section)
DisableCodecG729=yes | no
set parameter to control Packet Loss. Network Problem Threshold 1-99, 100 - disable. (Note: device should be re-provisioned. Supported only by WP4x0)
LossPktRateMin=0-100
set parameter to control Packet Loss. Critical Network Problem Threshold 1-99, 100 - disable. (Note: device should be re-provisioned. Supported only by WP4x0)
LossPktRateMax = 0-100
BLF will blinks in case when monitored user has active call+incoming call if "ActiveAndIncomingCall" or keep the old behavior if "ActiveCall". Default is old behavior. (Note: only for [wildixp2] section)
BLFNotifyType= ActiveCall | ActiveAndIncomingCall
force the failover pbx (sip server 2) with the value. Only ip addresses allowed. (Note: only for [wildixp2] section)
FailoverPbxIp = <IP address>