Page Comparison

To make any changes to config files, access them via SSH as root:

...

Collaboration 

Disable file transfer in Collaboration chat messages 

...

Change the default Departments tree separator

Anchor
departmentsastree departmentsastree

Starting from WMS 5.04.20220309.1, the Colleagues tab in Collaboration shows only the list of Departments and there is possibility to create a multilevel hierarchy of Departments and display them in a tree view. 

...

By default, only people added to rosterare shown on the Colleagues tab. To display all users registered on the PBX, add the following line to the /rw2/etc/env.custom.ini file:

...

COLLABORATION_WEBRTC_RELAYCANDIDATESONLY=true

Configure which numbers on mobile should be directed to native dialler

...

The option allows setting a specific GSM gateway for SMS sending for each separate user:

• Edit the config file /etc/wildix/smsd-route.conf by specifying user extension and MAC address of GSM gateway, for example:

  Code Block
  101,9c7533014b00 102,9c7533014b00 103,9c7533014b00 104,9c7533014b01

  
  

...

Dialplan

Exit code 0 from voicemail 

...

...

INACTIVITY_TIMEOUT_MINUTES = 120  

• Where 120 is the timeout in minutes (enter the preferred value)

The Maximum value is 600 (10 hours). In case you set the inactivity timeout to 0, it gets disabled. 

Integrations

Hotel PMS

...

Display user status in call groups as unavailable when it changes to offline

Starting from WMS 6.07.20240906.1, it is possible to configure display of user status in call groups as Unavailable when user status changes to offline.

To enable the option:

1. Add the following parameters to the /etc/callweaver/sip-general-custom.conf file:

change_cg_agent_status_on_unregistration=yes

2. Run the command:

callweaver -rx "sip reload"

By default, the option is disabled.

Integrations

Hotel PMS

WHoteld package supports some custom configuration parameters that can be changed by editing the file /etc/wildix/whoteld_manager_custom.conf.

...

• Create a new config file template.conf including GTM ID in the file /rw2/etc/pbx/, for example, use the command: 

  Code Block
  echo 'gtm=GTM-12345678' > template.conf

  where 123445678 is Google Tag Manager ID.

...

ECM is enabled by default. To disable it, add the following line in /etc/callweaver/res_fax_custom.conf:

...

Maximum transmission speed

...

On some iOS versions, there is an occasional issue of in which there can be no media after answering a call, in case the phone was locked and it is an API call by an external CRM or a call from Collaboration with Any selected as a device. If you encounter such an issue, to avoid it, you can add the following line it, you can add the following line to the /rw2/etc/env.custom.ini file:

ORIGINATE_VIA_ANY_DEVICE_TRANSFER=false

Prevent obsolete repeaters from upgrade

Starting from W-AIR firmware v.07.30.xx.xx and higher, old Wildix repeaters are no longer supported and need additional configuration to stay on previous firmwares to continue working. For old repeaters to work, you need to add the following parameter to the /rw2/etc/envprovision.custom.iniconf file:

ORIGINATE_VIA_ANY_DEVICE_TRANSFER=false

Prevent obsolete repeaters from upgrade

Starting from W-AIR firmware v.07.30.xx.xx and higher, old Wildix repeaters are no longer supported and need additional configuration to stay on previous firmwares to continue working. For old repeaters to work, you need to add the following parameter to the /rw2/etc/provision.conf file:

SupportObsoleteRepeater = yes 

The default value is “no”. When the parameter is enabled, the base stations automatically switch to the previous firmware on which the obsolete repeaters are supported (v. 06.xx.xx.xx)  

SupportObsoleteRepeater = yes 

The default value is “no”. When the parameter is enabled, the base stations automatically switch to the previous firmware on which the obsolete repeaters are supported (v. 06.xx.xx.xx)  

transmit_silence = yes

systemctl restart callweaver.service

...