Page Comparison

<div id="fb-root"></div>
<script>(function(d, s, id) {
  var js, fjs = d.getElementsByTagName(s)[0];
  if (d.getElementById(id)) return;
  js = d.createElement(s); js.id = id;
  js.src = 'https://connect.facebook.net/en_US/sdk.js#xfbml=1&version=v2.11';
  fjs.parentNode.insertBefore(js, fjs);
}(document, 'script', 'facebook-jssdk'));</script>

...

Overview and LED indicators

DaySaver Overview

Front panel:

Image Added
1 - SIM slot: insert and press a SIM card to the slot

...

7 - 2 antennas: one for data connections; another one - for calls and SMS

Rear panel:

Image Added

1 - DC 12V power supply (optional, WMP code: PS-12V2A)

...

...

After provisioning, the gateway appears in WMS:

• WMS -> Devices:

Image Added

• WMS -> Trunks:

Image Added

...

Backup for the voice service: DaySaver is placed between the customer’s existing network and a separate VoIP Network (over vlan, for example). If the PBX becomes unreachable over network, DaySaver automatically switches the connectivity to 4G / LTE.

Without DaySaver:

Image Added

With DaySaver:

Image Added

Backup for an entire office: DaySaver is placed between the router and the whole network of the customer. In case the office internet connection goes down, all traffic starts working via DaySaver:

Image Added

Enable VoLTE 

VoLTE Network allows using DaySaver as a backup for Cloud PBXs, as a backup for the cable Internet connection, or, even as the only Internet access for small offices or during the events.

...

• Go to Network -> VoLTE 
• Check off Enable in Status field
• Click Save
• Confirm by clicking Apply
  
  Image Added
  

Set uplink config

The uplink config should be set to "WAN Master, VoLTE Slave" with tracking IP addresses set to something publicly accessible, in this example we use 8.8.8.8.

...

If WAN loses 3 pings to 8.8.8.8, it failovers to VoLTE. When WAN becomes available again (Count of up), WAN becomes the master again. 

Image Added

Enable DHCP Server

...

• Go to Network -> DHCP Server
• Check off Enable
• DHCP Server settings must have default gateway as the DaySaver LAN IP address
• DNS Servers must be reachable via LAN

Image Added

If you want to use DaySaver as a backup for a single switch:

...

• Go to Network -> Setting
• Plug WAN & LAN port into existing Switch / Router
• Allow devices on existing network to get IP addresses from DHCP Server provided from DaySaver:

Image Added

Status Page Example 

• Go to Status -> Overview
• Check the network status:
  Image Added

Test the network topology

...

• Go to ipchicken.com when existing router internet is up 

  
  Image Added

• Go to ipchicken.com when existing router internet is disabled or turned off 

  
  Image Added

Use DaySaver as Trunk backup (optional)

...

• Once the device is provisioned, assign main Dialplan procedure to DaySaver. This can be done in WMS -> Trunks -> GSM/UMTS -> Edit trunk settings

• Where Number of sim is seen, this is the number that is dialled when the GSM number hits the PBX. This number also needs to be added to main Dialplan procedure. For example, 34649237852 is added to Number of sim and also added to the Dialplan procedure 
  
  Image Added
  Image Added

  Number of sim should match the number under DaySaver VoLTE settings: go to Trunk -> VoLTE and change make sure Autodial Number matches the number you have applied to main procedure: 
  
  Image Added
  
  Image Added

• Go to WMS Devices -> select DaySaver and click Configure / Sync device to pass the configured parameters
• Once you have saved and applied all settings, you are able to call the mobile number associated with the SIM card which will hit the PBX

...

...

• Hold and press both Reset and Reboot buttons, power up the device via WAN/ PoE and keep holding the two buttons for 30 seconds when plugging in. This will put the device into recovery:
  
  Image Added
  

Step 2

• Run a cable between the LAN port and your laptop/ machine ensuring the DaySaver is still powered up 

  Note
  Note: If you machine uses Wi-Fi, please disable it as this prevents you browse to the recovery interface (192.168.11.1).

  
  

Image Added

Step 3

• Once connected, you are be able to browse to the recovery interface “192.168.11.1” and upload the firmware file
• Click Choose file and select the firmware version from your machine
• Click Upload, then wait 10 - 15 minutes for this process to be completed

Image Added

Image Added

Step 4

• Remove the LAN cable, ensuring the WAN cable is still connected and reboot
• The recovery is completed. You are now be able to use the device and browse IP to provision
  
  Image Added